datasheet | september 2013 fiber optics | rev 2013.09 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. applications catv systems long distance rf/microwave fiber optic communication links sensing and control systems high-performance supertrunking links high power distri bution networks redundant ring architectures fttx networks features full function fiber optic pre-amplifier low noise figure (nf typ < 3.3 db) pin > -45 dbm pout (saturated): +14 dbm small signal gain > 37 db low electrical power consumption output isolation > 40 db polarization dependant gain < 0.1 db polarization mode dispersion < 0.2 ps output return losses < -40 db output residual pump power < -40 dbm emcore?s mafa 1014-pa optical preamplifier erbium doped fiber gain block module is an ideal building block for system integrators to extend the fiber link for long-haul signal transport. the mafa 1014-pa optical preamplifier series gain blocks are designed to meet the most demanding noise performance requir ements of fiber optic communications and control systems and performs all the functions r equired of an optical preamplifier for system integration. the mafa 1014-pa optical preamplifier provides output optical isolation for stable, low noise operation. the output optical signal power level is detected for monitoring and control. the very low level input optical signal is amplified with active output power control for constant current mode operation. the compact mechanical footprint of the mafa 1014-pa optical preamplifier allows using this unit to be installed in small space environments. general and mechanical specifications * - extended temperature range of ? 40oc to +75oc is also possible ** transient pulse to +x.x vdc + 5% for < 100 msec electrical power must be applied to the unit only after launching input optical parameter min typ max units comments operating wavelength 1532 - 1565 nm standard operating case temperature 0 - 50 c standard* storage temperature -40 - 85 c standard operating humidity 20 - 85 % non-condensing voltage supply range - +12/+5/+3.3 - vdc all versions** optical connectors - sc; fc; e2000 - - user specified dimensions (mm) - 70 x 90 x 15 - mm all versions mafa 1014-pa optical preamplifier erbium doped fiber preamplifier
datasheet | september 2013 fiber optics | rev 2013.09 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. optical/electrical characteristics 1 property unit limit model 1400 comments (note 1) operating input power pin (dbm) max 0 - operating input power pin (dbm) min -45 - saturated output power pout (dbm) nominal 14 +/- .25 (notes 2,3) noise figure nf (db) max 3.3 db (note 4) output power stability (db) max +/- 0.1 (note 5) power consumption (steady state) psys(w) max 2 70c case notes: 1. unless stated otherwise, all specif ications apply over the full operat ing temperature and humidity ranges 2. measurement variations 3. measured @ 1550 nm and pin = -4 dbm 4. measure @ 1550 nm and pin = -30 dbm 5. over polarization and temperature outline drawing (dimensions in mm) mafa 1014-pa optical preamplifier erbium doped fiber preamplifier
datasheet | september 2013 fiber optics | rev 2013.09 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. compliance and reliability information fcc: subpart b. part 15 class ?a?: unintentional radiators en 55013: sound and television broadcast receivers and associated equipment ? radio disturbance ch aracteristics- limits and met hods of measurements ? electric field radiation emissions (2001) fit rate: 90% level of confidence - 290 @ 25 c electrical connector pinout pin # designation pin # designation 1 +12 vdc/+5 vdc/+3.3 vdc 16 led_laser_on 2 +12 vdc/+5 vdc/+3.3 vdc 17 n/a 3 +12 vdc/+5 vdc/+3.3 vdc 18 pump_bias_alarm * 4 +12 vdc/+5 vdc/+3.3 vdc 19 loss_input_power * 5 gnd 20 loss_output_power * 6 gnd 21 n/a 7 rs232_rx 22 n/a 8 rs232_tx 23 n/a 9 gnd 24 n/a 10 gnd 25 n/a 11 led_comm 26 n/a 12 edfa_reset 27 n/a 13 edfa_disable 28 n/a 14 pout_mute 29 n/a 15 edfa_temp_alarm * 30 n/a * - software adjustable parameters; logic levels (low / high) tbd ordering information mafa-pa-1014 - - - connector option temp options voltage options sc1 - sc/apc s ? standard 1 - +12 vdc s21 - sc/pc e ? extended 2 - +5 vdc fc1- fc/apc - 3 - +3.3 vdc fc2- fc/pc - - ec1-e2000/apc - - example: mafa-pa-1014-sc1-s-2: 14 dbm pre-amp gain block with sc/apc optical connectors, standard temperature range, +5 vdc power supply mafa 1014-pa optical preamplifier erbium doped fiber preamplifier
datasheet | september 2013 fiber optics | rev 2013.09 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. laser safety information this component product does not meet the applicable requirements of 21 cfr 1010 & 1040 and is classified as a class iiib laser product based on the maximum optical output power defined below. during use as intended, the laser energy is fully contained within the fiber network such that there is no accessible laser radiation and would meet the requirements for a class i laser product. wavelength = 1532 ~ 1565 nm (dependent on input source) maximum output power = 200 mw mafa 1014-pa optical preamplifier erbium doped fiber preamplifier
|
